Snap-on 5000-ST Instrukcja Użytkownika Pobierz pdf (Strona 63)

Strona główna
Snap-On
Narzędzia
5000-ST
Instrukcja Użytkownika

Pobierz
Podziel się

Dzielenie się
Dodaj do moich podręczników
Drukuj

MANUAL LOADER CHAPTER 6

6-62

Loader Rear Panel Controls

The 2000-600-02 Manual Loader rear panel is shown in Figure 6-3.

Figure 6-3: 2000-600-02 Manual Loader Rear Panel Controls

A- Fuse

The loader power supply is protected with a 1 amp slo-blow fuse.

B- Voltage Select

A selector switch allows the loader to use both 110VAC or 220VAC.

C- AC Power Input

The loader uses either 110VAC or 220VAC power. The loader connects to the SURETEST Base

Unit by the 2000-117 cable.

D- Solenoid Control

AC power is applied to the loader to operate a pair of safety solenoids used to protect the

transducers from overloading. Should the applied torque exceed 110% of the transducer capacity,

in either CW or CCW directions, the Base Unit energizes the solenoids to lock the hand crank.

1 2 ... 58 59 60 61 62 63 64 65 66 67 68 ... 73 74

TABLE OF CONTENTS 2
Using this Manual 4
CAUTION 5
Read All Instructions 6
PRODUCT DESCRIPTION 8
Introduction 9
Functional Descriptions and 11
Specifications 11
Base Unit 12
FRONT PANEL 13
SURETEST DISPLAY 14
Power Up Sequence 14
Setup Mode 15
5. Auto Settings 16
3. Select Language 16
4. Manufacturer’s Defaults: 16
6. Edit Limits 17
7. Clock Adjust 17
8. Calibration 17
+/-100 mV 19
F- PRINTER PORT (DB-9P) 20
G- OPTIONAL (DB-9P) 20
SURETEST Transducers 21
Serial Communications 23
Manual Loader Specifications 24
SETUP AND PROGRAMMING 25
Back panel connections 26
Base Unit Controls 27
Setting up Date and Time 29
Set-up AUTO CLEAR 30
DATA LIST Memory 31
SURETEST TORQUE CALIBRATION 33
SYSTEM SETUP 33
WARNING 34
Example: 35
Testing Power Tools 36
Non-Impact Tools 36
SPC PRINT-OUT 40
Displaying Data List 42
Calibration 43
Mounting Details 44
Torque Under 250 ft lb 45
Torque Over 250 ft lb 45
Quick Check 47
2000-12-02 49
2000-13-02 49
2000-14-02 49
2000-400-02 49
Torque Calibrations 50
Calibration CW: 51
Calibration CCW: 53
Procedure 54
Calibrate tester 55
Gravitational Effects 57
(2000-600-02) 58
Functional Description 60
Torque Tester/Calibrator 60
A- Transducer Mounting 61
IMPORTANT 62
Loader Rear Panel Controls 63
A- Fuse 63
B- Voltage Select 63
C- AC Power Input 63
D- Solenoid Control 63
Ball Handle Adaptor 64
A- Quick Release Pins 65
C & D- Bracket Knobs 65
E- 4-in-1 Adapter Bracket 66
Extension Arm (Accessory) 67
Torque Driver Testing 68
Torque Multiplier Testing 68
Appendix A 68
Accessories 68
ACCESSORIES APPENDIX A 69
2000-100-02* Roll cabinet 70
Calibration Accessories 73

Komentarze do niniejszej Instrukcji

Brak uwag

Snap-on 5000-ST Instrukcja Użytkownika Strona 63

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Narzędzia Snap-on 5000-ST